Wall clocks gradually went from being a practical necessity in our home to becoming decorative and retro. We don’t really need a physical wall clock anymore these days when we have the convenience of checking our phones, wristwatches or having the time displayed on the kitchen appliances.

DIY wall clock using an embroidery hoop

But rather than considering it outdated and useless, we can focus more on the aesthetics and we can work on beautiful projects like making a DIY wall clock using an embroidery hoop and a few buttons. Here’s what you need to know about this project:

Materials you’ll need for the embroidery hoop wall clock:

How to craft the embroidery hoop wall clock:

Step 1: Gather all the supplies

Get all the supplies that you’re going to need ready and place them on your work surface. It’s nice to have them close at hand and organized so you don’t have to constantly look for them around the house. Pick a clock mechanism that you like, with a design that suits your style. Perhaps you can find an old clock that you can take apart and reuse the mechanism from that. It would be a nice way to recycle a few of the components. 

DIY wall clock using an embroidery hoop - materials

Step 2: Paint the embroidery hoop

Take the hoop apart and paint the outer one using the cream-colored acrylic paint. It’s not necessary to paint the other one as well since it won’t be visible. 

Paint the embroidery hoop

Make sure you paint the exterior and the edges too. These surfaces will be visible once the clock is put together so you want them to look nice and clean all around. 

Step 3: Secure the fabric between the two hoops

Once the paint is dry, take the piece of linen fabric that you’ve prepared in advance and center it over the smaller hoop. Then place the other one over it so that the fabric is secured between the two hoops. Make sure it’s nice and tight. 

Secure the fabric between the two hoops

You only need a small piece of fabric for this project. A square would do, one that’s slightly bigger than the embroidery hoop. 

Make sure the fabric is tightly stretched between the hoops without any wrinkles. The placement at this point will be permanent. 

Step 4: Cut the excess fabric

If you’re happy with how the fabric is centered and stretched you can proceed to cut the excess around the hoop. Make sure to leave a little bit of fabric around the outside, cutting in a circle and getting rid of the corners and anything that’s too much. Don’t leave too much of a trim. 1 cm or so is enough. 

Cut the excess fabric

Step 5: Glue the fabric trim to the hoop

The reason why you shouldn’t leave a lot of fabric around the outside is because you’ll now have to fold it and glue it to the interior of the hoop. That will give the clock a clean and chic look without any messy parts. 

Glue the fabric trim to the hoop

Start from the top and fold the linen fabric a little bit at a time, adding a little dot of hot glue each time and making sure it holds. Press the fabric in place for a few seconds each time. 

Step 6: Sew on the large buttons

As you may have noticed, not all the buttons are the same size or color. They could be, of course, but using different types gives the clock a bit more character. You can use four large buttons for the 12, 3, 6 and 9 o’clock placing them at the four cardinal points on the surface of the clock. 

Sew on the large buttons

Sew each button onto the canvas using a needle and some white or cream-colored thread. Make sure the placement is right before you go ahead and secure them in place. 

Be sure to do a double knot at the back so the buttons don’t fall off. 

Step 7: Add the next four buttons

It’s then time to sew on the next four buttons. These should be smaller than the first four ones and it could be nice for them to also have a slightly different color as well. Place these to the right of the existing buttons, where 1, 4, 7, and 10 o’clock would be. 

Add the next four buttons

Like before, make sure they’re tight and secure and they stay in place. Don’t worry, the back side won’t be visible and doesn’t need to be perfect. 

Step 8: Add the final four buttons

The last four buttons can be even slightly smaller than the previous ones and again in a slightly different color. They’ll fill the remaining four spaces on the surface of the clock, completing the circle. Make sure they’re all evenly spaced apart. 

Add the final four buttons

Sewing the small buttons is no different than what you did before. Position them in place, run some thread through the two holes a few times and then turn the hoop and secure them in the back as well. 

Step 9: Add a tiny decoration on top of each button

When you’re done sewing all the buttons and you’re happy with how they’re arranged, take your hot glue gun and put a tiny dab of glue to the center of each button. Then press a little decoration on top of it and press gently. These decorations can be tiny buttons, beads, rhinestones and various other things. They’ll create a nice layer and will give your clock a bit more style and character. 

Add a tiny decoration on top of each button

Start with the button at 12 o clock and go around until you’ve decorated all the buttons. Place these little ornaments at the center of each one to hide the thread. 

Step 10: Install the clock mechanism

This is the final step of crafting a DIY wall clock and the one which involves installing the actual clock mechanism. First make a tiny hole at the center of the clock for the mechanism to fit through. You can do that with your scissors. Then take the back piece which holds the batteries and push it through, securing it in place. Then add the hands and you’re done!

Install the clock mechanism

The hole at the center doesn’t need to be big. It just needs to let the central rod of the mechanism to fit through so the front and back sections can be secured together. 

The clock hands are added at the very end and once they’re in place this project is basically complete. After that you can add the little ribbon bow at the top to hide the hoop screw if you want. Just take a piece of silk ribbon and make a small loop, then run another piece across and glue it onto the clock at the top, just above 12 o’clock. 

The post How To Make A Wall Clock From An Embroidery Hoop And Linen Fabric appeared first on Home Decorating Trends – Homedit.

Leave a Reply

Your email address will not be published. Required fields are marked *